Skip to content
ARYAN TRANSPORTFreight & Logistics · Est. 2007
Bills of lading, rate confirmations and a laptop on a bright freight office desk

Shipping Guide · 9 min read

How to choose the right trailer for your freight

The right trailer protects your freight, keeps the load legal and avoids paying for capacity you do not need. Here is how the main options compare and how to decide.

Start with three questions

Most trailer decisions come down to three questions. First, does the freight need protection from weather or temperature? Second, how will it be loaded and unloaded: from a dock, by forklift from the side, by crane from above or driven on? Third, how big and heavy is it, especially the largest single piece? With those answers, the choice usually becomes obvious.

Enclosed trailers: dry vans and reefers

A 53-foot dry van is the standard choice for palletized and boxed freight that loads at a dock. Inside dimensions are roughly 52 to 53 feet long, about 8 feet 2 inches wide and 8 feet 6 inches to 9 feet high, and a typical load holds 26 standard pallets on the floor or about 42,000 to 45,000 pounds, depending on the tractor and trailer weight.

A refrigerated trailer, or reefer, looks similar but has insulated walls and its own temperature control unit. Reefers carry slightly less weight and space than dry vans because of the insulation and the unit. Use a reefer for fresh, chilled and frozen goods, and in winter for freight that must not freeze. Always give the set point and say whether the unit should run continuously or cycle.

For smaller loads or deliveries to locations without a dock, straight trucks of 16 to 26 feet with liftgates and cargo vans are often the better fit. They are also the usual choice for expedited freight.

Open-deck trailers: flatbed, step deck and conestoga

Flatbeds are 48 or 53 feet long and about 8 feet 6 inches wide, with a deck around 5 feet off the ground. Because they load from the sides or above, they suit steel, lumber, pipe, building materials and machinery that is loaded by forklift or crane. Freight that must stay dry needs tarps, which add cost and time.

A step deck has an upper deck at the front and a lower main deck about 3 feet 6 inches off the ground. The lower deck lets taller freight, up to about 10 feet, travel without exceeding the usual 13 feet 6 inches legal height. Step decks are common for equipment, vehicles and tall crates.

A conestoga is a flatbed or step deck with a sliding tarp system. It gives the loading flexibility of an open deck with weather protection and no manual tarping, which makes it popular for high-value machinery and finished goods that cannot be loaded at a dock.

Heavy haul: RGN and lowboy trailers

When freight is too tall or too heavy for a step deck, the answer is usually a removable gooseneck (RGN) or another lowboy design. The deck sits very low, often under 2 feet, and the neck detaches so equipment can be driven on from the front. Standard RGNs carry around 40,000 to 42,000 pounds legally, and multi-axle configurations carry much more with permits.

Heavy haul moves need the full specifications of the load: weight, length, width, height and how it will be loaded. The trailer choice affects permits, routes and escorts, so it is planned together with the route rather than separately.

Containers and intermodal

Imported freight often arrives in 20-foot or 40-foot ocean containers, which move on a chassis for drayage between the port or rail ramp and a warehouse. For long inland moves, it can be cheaper to transload the freight into a 53-foot domestic trailer or a domestic intermodal container that travels by rail, then by truck for the last miles.

Common mistakes to avoid

  • Booking a flatbed for freight that cannot get wet, without arranging tarps or a conestoga.
  • Forgetting that a forklift cannot side-load a dry van, so dock access matters.
  • Underestimating the height of equipment once it is on the trailer deck.
  • Assuming a reefer is fine for freight that is not food: it is, but give the set point.
  • Ordering a full 53-foot truck for six pallets when a partial or LTL would cost less.

If you are not sure, ask. Describe the freight, how it loads and the dimensions of the largest piece, and we will recommend the option that is safe and costs the least.

Weight limits and why they matter

The legal gross weight limit for most five-axle tractor-trailers on U.S. interstates is 80,000 pounds, including the truck, the trailer, fuel and the driver. That is why the usable payload of a dry van is around 42,000 to 45,000 pounds rather than more, and why a reefer or a heavy tractor reduces it further. Axle weights also have their own limits, so heavy freight must be positioned correctly on the trailer, not just kept under the total.

Loads that cannot be divided and exceed these limits need overweight permits, specialized trailers with more axles and sometimes route planning around bridges. If your freight is close to the limit, tell us the exact weight and how it is distributed, and we will make sure the right equipment is assigned.

When two trailer types both work

Sometimes more than one trailer would do the job, and the choice comes down to cost and convenience. Machinery that fits in a van may still be cheaper on a flatbed if the shipper can only load it by crane. Freight that could go on a flatbed with tarps might be safer and faster on a conestoga. A small load that fits a straight truck may cost less as a volume partial on a 53-foot trailer if the timing is flexible. We look at those options when we quote and tell you when a different trailer would save money or reduce risk.

Questions

Quick answers

What is the maximum weight on a standard truck?

Most five-axle trucks are limited to 80,000 pounds gross on interstates, which leaves roughly 42,000 to 45,000 pounds of payload in a dry van, depending on the equipment.

How many pallets fit in a 53-foot dry van?

Typically 26 standard 48 by 40 inch pallets loaded straight, or up to 30 when pinwheeled, depending on pallet size and stackability.

When do I need a step deck instead of a flatbed?

When the freight is taller than about 8 feet 6 inches. A step deck's lower deck allows up to about 10 feet while staying under the usual legal height.

Do I need permits for oversize freight?

Yes. Loads over legal width, height, length or weight need state permits, and some also need escorts or route surveys.

Have freight that needs to move?

Send the lane, the equipment and the date. Our team prices standard truckload lanes within the hour on business days, and the dispatch desk answers around the clock.